Skip to main content

Stringer Math

Okay I have done some math on my stringers and bulkheads...let me know if this makes sense.

There is 519" of area on both sides of the stringers
288" on both sides of the bulkheads
So add those together and that give me 807" of total area or 67.25' or 22.42 yards.

I figured that I will use 4" 1 1/2oz CSM tape for the first layer
- Which uses 1.25gal of resin for a whole roll (110yards) but I will only figure for 25 yards...or .23 of a whole roll
- So .23 x 160oz of resin (1.25gal) = 36.8oz of resin for the 1st layer

Layer 2 I will use 6" 1 1/2oz CSM tape
- Which uses 1.75gal of resin for a whole roll (110yards)
- .23 x 224oz of resin (1.75gal) = 51.52oz of resin for the 2nd layer

Layer 3 I will use 6" 1708 Biaxial and according to this website 1708 takes a little less resin to wet out than 1 1/2oz CSM so I will figure at CSM values:
- .23 x 224oz of resin (1.75gal) = 51.52oz of resin for the 3rd layer

Layer 4 will be a copy of the 3rd layer:
- .23 x 224oz of resin (1.75gal) = 51.52oz of resin for the 4 layer

So in summary the parts list for glassing the stingers w/o capping is:
1. 25yards 4" 1 1/2oz CSM tape
2. 25yards 6" 1 1/2oz CSM tape
3. 50yards 6" 1708 Biaxial tape
4. 181.36oz of resin (I will buy 5gallons just to get started)

Comments

Post a Comment

Popular posts from this blog

Vacation

We went on vacation last week to Colorado and Utah via Kansas and Missouri. We saw 7 states in 9 days, took off on Thursday July 3 around 2 in the afternoon and headed west. Our first stop was in Topeka, Kansas where we spent the night. The next morning we got up and left after a good breakfast. Around 3 in the afternoon we got our first sight of the mountain and it was Pike's Peak over looking Colorado Springs, Co. That is where we spent the next 3 nights and the sights that we saw were Pike's Peak, Seven Falls, Garden of the Gods, and Manitou Springs. So we spent Friday, Saturday , and Sunday nights there. On Monday we took off for Cortez, Co. That is close to Mesa Verde. On the way there we were able to take in some good places like the Continental Divide and Treasure Falls. Once we got there we packed it up for the evening. The next day Tuesday brought us to Mesa Verde. There we spent the day looking at the ruins of the ancient Puebloan people who built the famous cli...
2 comments
Read more

Glued...

April 1, 2012 The Stringers and Bulkheads are now glued into the boat. It has been a long day. We (my brother in law, Jack came over to help) started the day by bracing the center stringer that comes out from under the bow section. Onc e that was done we mixed up our first batch of "Peanut Butter". We started with 1 cup of resin and the right amount of hardener, then about 3 pinches of 1/4 inch Chopped Strand Mat and then Cabosil to thicken up the mixture to the consistency of "Peanut Butter". It worked out pretty well. While that was hardening we went to work on scuffing the resin that was spread on the stringers and bulkheads. We wanted to sand those before putting them into the boat. That took about an hour so then it was lunch time. We noticed that the thickened resin we made was still pretty soft so we moved the boat out into the sunlight while we ate lunch. Sure enough when we came back out the resin had kicked and was already pretty solid. We...
1 comment
Read more

Deck Gel Coated...

May 25, 2012 I took this day off of work to work on the boat.  I wanted to get the deck ready to be Gel Coated which was ordered and received. First I gave the deck a good sanding.  It had been a while since we fiberglassed so I wanted to make sure that the surface was ready to receive the Gel Coat.  After I was finished with the sanding I moved the boat outside for a good cleaning.  Using an air compressor (Thanks Jack) I blew off the deck and then gave it a good acetone wash. That pretty much took up the entire day.  I had to wash the van because it got covered with dust.  Sorry no pictures of the progress today. May 26, 2012 The deck is now Gel Coated.  The four person team of Jack, Sally, Nina and myself worked for a long time again to get this job accomplished. We took the pigment for a gallon and added it directly to the container and then took turns shaking the can to thoroughly mix the color.  I believe that it looks great!...
Post a Comment
Read more